CD/DVD 无法正确刻录

有几种情况可能会导致 MediaMonkey 刻录引擎不兼容：

  1. 在某些系统上，刻录需要管理员权限。您可能会收到错误“错误：没有可写驱动器！”。您可以右键单击启动 MediaMonkey 的位置，然后选择以管理员身份运行。
  2. MediaMonkey 有时与虚拟 CD 软件（例如 Nero ImageDrive）不兼容，该软件允许您将 CD 映像写入硬盘驱动器。在这种情况下，它可能会导致 MediaMonkey 在刻录 CD 或 DVD 时暂时冻结、崩溃或锁定设备。要解决此问题，只需卸载或禁用 ImageDrive。
  3. 如果您有多个驱动器，请尝试断开任何外部 CD/DVD 驱动器——在某些系统上，它们可能会干扰内部驱动器。
  4. 如果您收到错误“无法刻录图像布局”，则可能是由于 MediaMonkey 无法使用特定品牌的媒体以选定的速度成功刻录磁盘。尝试以较低的速度刻录。此外，尝试将目标文件名掩码简化为更简单的内容，例如 <艺术家> – <标题>
  5. 如果问题仅与音频 CD 有关，请在刻录向导的最后一页尝试：
    • 禁用‘即时音频刻录’
    • 降低燃烧速度
    • 从“一次读取磁盘”更改为“一次读取磁道”
    • 禁用 CD-Text 刻录
  6. 刻录机硬件直接报告的几个刻录错误可能表明存在硬件问题。这些包括：
    • 感知代码 0（无感知） ——如果驱动器停止刻录并且介质停止旋转，则很少发生
    • 感知代码 1（恢复错误） – 警告错误消息，表示操作过程中出现问题
    • 感知代码 2（未就绪） – 驱动器和插入的媒体状态，MediaMonkey 内部处理并提示用户结果
    • 检测代码 3（介质错误） – 与介质相关的错误，表示介质损坏或不支持的刻录速度导致刻录失败
    • 感知代码 4（硬件错误） – 由于无法执行请求的命令而导致驱动器硬件相关错误
    • 感知代码 5（非法请求） ——最常见的情况是，由于受保护的磁盘或不兼容的媒体等媒体问题，硬件拒绝执行或无法完成命令
    • 感知代码 6（单元注意） ——与设备通信时在刻录软件中处理的通信代码和响应代码。

有关错误代码的详细信息，请访问http://users.telenet.be/erik.deppe/troubleshooting_errorcodes.htm

适用于:

Translated automatically (see original)

CDs / DVDs don’t burn correctly

There are a couple of situations that can cause incompatibilities with MediaMonkey’s burning engine:

  1. On some systems burning requires Administrative rights. An error you may receive is ‘Error: No writable drive!’. You can right click where you launch MediaMonkey and select Run as Administrator.
  2. MediaMonkey is sometimes incompatible with Virtual CD software such as Nero ImageDrive, that allows you to write to a CD image on the hard drive. In such cases, it can cause MediaMonkey to temporarily freeze, crash, or lock the device when burning a CD or DVD. To resolve this issue, simply uninstall or disable ImageDrive.
  3. If you have multiple drives, try disconnecting any external CD/DVD drives–on some systems, they may interfere with internal drives.
  4. If you receive an error ‘Could not burn image layout’ it may be caused by MediaMonkey being unable to successfully burn the disk at the selected speed with the particular brand of Media being used. Try burning at a reduced speed. Additionally try to simplify Destination Filename mask to something simpler like <Artist> – <Title>
  5. If the problem is specific to Audio CDs, on the last page of the burn wizard try:
    • Disabling ‘On the fly audio burning’
    • Lower the speed of burning
    • Change from ‘Disk at once’ to ‘Track at once’
    • Disable burning of CD-Text
  6. There are several Burn errors that are directly reported by burner hardware that may indicate a hardware problem. These include:
    • Sense code 0 (No Sense) – Occurs rarely if the drive simply stops burning and media stopped spinning
    • Sense code 1 (Recovered Error) – Warning error messages that there was a problem during the operation
    • Sense code 2 (Not Ready) – Drive and inserted media state which MediaMonkey handles internally and user is prompted with result
    • Sense code 3 (Medium Error) – Media-related error that indicate either damage to the media or unsupported burn speed that causes burn to fail
    • Sense code 4 (Hardware Error) – Drive hardware-related errors due to failure to execute the requested command
    • Sense code 5 (Illegal Request) – Most commonly occurs when hardware refuse to execute or fails to complete a command due to media issues such as Protected Disk or incompatible media
    • Sense code 6 (Unit Attention) – Communication codes and response code that are handled within burning software when communicating with device.

Detailed info on error codes can be found at http://users.telenet.be/erik.deppe/troubleshooting_errorcodes.htm

Applies to:

Hide original

这篇文章有帮助吗？