无需 iTunes 即可安装 Apple 同步驱动程序

要与 Apple iOS 设备同步，Windows 版 MediaMonkey 需要安装最新的 Apple Mobile Device Drivers。通常，安装 iTunes 桌面版即可完成此操作，但如果您不想安装 iTunes，并且精通技术，也可以使用多种方法独立于 iTunes 安装 Apple Mobile Device Drivers 及其服务。请注意，这些方法不支持 iOS 同步，因为它们可能不适用于所有用户。

如果您之前安装/卸载过 iTunes：

  1. 从 C: 驱动器上的驱动程序残留副本安装驱动程序
    • 导航至 C:\Program Files\Common Files\Apple\Mobile Device Support\Drivers
    • 右键单击 usbaapl64.inf，然后单击“安装”
  2. 或者，使用设备管理器安装驱动程序
    • 连接您的 iPhone/iPad
    • 单击 Windows 开始按钮并运行“设备管理器”
      • 单击通用串行总线设备/控制器，然后右键单击 Apple Mobile USB 设备以更新并启用它们
      • 或者，单击“便携式设备”>“Apple iPhone”，然后右键单击以“更新并启用”

如果你从未安装过 iTunes

  1. 直接从 iTunes 安装驱动程序（无需安装 iTunes）
    • 下载最新的 iTunes桌面版本（ 64 位版本| 32 位版本）。
    • 下载并安装可以打开和提取 CAB 文件内容的程序，例如7-zip或WinRar 。
    • 使用 7-zip 检查 iTunes 安装程序 iTunes64Setup.exe或 iTunesSetup.exe （您在步骤 1 中下载）的内容（右键单击，7-zip，打开存档）。7-zip 将显示安装程序内的文件。
    • 将 AppleMobileDeviceSupport64.msi或 AppleMobileDeviceSupport.msi从安装程序文件提取到您的硬盘。
    • 运行 AppleMobileDeviceSupport64.msi或 AppleMobileDeviceSupport.msi
    • 安装 Apple Mobile Device Support 后，将您的 iOS 设备连接到您的 PC，Windows 应该能够正确检测到它。
    • 启动 MediaMonkey 后您的Apple 设备将被检测到，以便您可以使用 Windows 版 MediaMonkey同步到该设备。
  2. 或者，使用第三方应用程序安装驱动程序（无需安装 iTunes）（请注意，Apple 和 MediaMonkey 不支持这些应用程序）。可能的选项包括：

无论采用哪种方法，请确保只安装一组驱动程序以避免冲突，并注意，在您连接设备时响应设备提示“信任”此计算机之前，该设备将不会在 Windows 中可见。

Applies to: ,

Translated automatically (see original)

Installing Apple Sync Drivers without iTunes

To Sync with Apple iOS devices, MediaMonkey for Windows requires the latest Apple Mobile Device Drivers to be installed. This is normally done by installing the iTunes desktop version, but if you prefer not to install iTunes, and are technically inclined, you can install the Apple Mobile Device Driver and its services independently of iTunes using a number of approaches. Note that these approaches aren’t supported for iOS synchronization as they may not work for all users.

If you’ve previously installed/uninstalled iTunes:

  1. Install the drivers from a residual copy of the drivers on your C: drive
    • Navigate to C:\Program Files\Common Files\Apple\Mobile Device Support\Drivers
    • Right-click on usbaapl64.inf and click ‘Install’
  2. OR, Install the drivers using the device manager
    • Connect your iPhone/iPad
    • Click the Windows Start button and run the ‘Device Manager’
      • Click Universal Serial Bus devices/controllers and right-click on the Apple Mobile USB Devices to Update & Enable them
      • OR, Click Portable devices > Apple iPhone and right-click to Update & Enable it

If you’ve never installed iTunes

  1. Install the drivers directly from iTunes (without installing iTunes)
    • Download the latest desktop version of iTunes ( 64-bit version | 32-bit version ).
    • Download and install a program that can open and extract contents from a CAB file such as 7-zip or WinRar .
    • Inspect the content of the iTunes installer iTunes64Setup.exe or iTunesSetup.exe (that you downloaded in step 1) with 7-zip (right click, 7-zip, Open archive). 7-zip will show the files inside the installer.
    • Extract AppleMobileDeviceSupport64.msi or AppleMobileDeviceSupport.msi from the installer file to your harddisk.
    • Run AppleMobileDeviceSupport64.msi or AppleMobileDeviceSupport.msi
    • After Apple Mobile Device Support have been installed, connect your iOS device to your PC and Windows should be able to detect it correctly.
    • Start MediaMonkey and your Apple device will be detected, so that you can use MediaMonkey for Windows to Sync to the device.
  2. OR install the drivers without installing iTunes using a third party app (note that these aren’t supported by Apple or MediaMonkey). Possible options are:

Whichever approach you take, ensure that only a single set of drivers is installed to avoid conflicts, and note that the device will not be visible in Windows until you respond to the device prompt to ‘Trust’ this computer when you connect it.

Applies to: ,

Hide original

这篇文章有帮助吗？